- Product Description
GM245 Fuel Injector Seals ToolsWhen you want to change the seal ring on the top of the injector, You may find that it is very difficult to put the seal ring into the groove of the injector. Our Fuel Injector Seals Tools can help you to change the seal ring easily. Premium Material: Made from quality steel, precision cutting to make each part is manufactured to specifications using. High precision and hardness ensure reliable long-term service.
Fits for General Motors 2.0L & 3.6L engines with Hitachi fuel injectors [2010-2017]; Fits for GM 2.0L, 2.5L, 5.3L & 6.2L engines with Bosch, Continental Delphi fuel injectors [2012-2017]; Fits for Subaru 2.0L/2.4L turbo engines [2014-2019]. Fits for Holden Colorado 7 2016 Package Includes: 1 × Seal Sizer 1 × Installer Pusher 2 × Long Seal Installer Guide 2 × Short Seal Installer Guide
Easily remove and replace the old seals for reusing an injector: Step 1. Cut off the old Teflon seal near the tip of the injector; Step 2. Place the pilot cone on the tip of the injector; Step 3. Push the new seal on the cone; Step 4. Use the installer pusher to push the seal into the groove of the injector; Step 5. Use the seal sizer tool to compress the Teflon seal to the correct size; Step 6. Finish! (EN-49245 must be used to install the seals correctly and to ensure they are sized correctly for leak-free operation.) 6706 Injector Rail Assembly Remover ToolUsed for the Hitachi SIDI system on 2010 LF1 3.6L V6 and LAF 2.0L ECOTEC has two seals on each injector, and these seals are installed with very tight tolerances. Once the engine has been run, injector and rail removal is very difficult, and the assembly must be removed as straight as possible to prevent the chance of damaging an injector bore in the cylinder head, or to the mount assembly. Each mount assembly contains an isolator, and cannot have any force applied to the mount for removal.
Universal Fit for most of vehicles. Fits for 2007 - 2014 General Motors direct injection vehicles. Fits for Cadillac Saturn Pontiac Chevrolet direct injection engines, Fits for 2007 - 2014 4.3L 3.6L 3.0L GDI V6, 2.5L 2.4L 2.0L GDI I-4. Note: If you are working on a 5.3L or 6.2L you will need 2 sets.
Usage Guide: Step 1. Remove the fuel injection fuel rail noise shield. Disconnect the electrical harness from the fuel rail harness connection. Disconnect all 4-fuel injector electrical connections. Remove the fuel rail assembly retaining bolts. Note: Use care to avoid contact with the fuel rail harness during special tool installation and fuel rail removal. Step 2. Install EN-49248studs (1) into the 2 center fuel rail assembly retaining bolt locations. Tighten the studs to 22-Y(16-lb-ft). Install EN-49248 remover-(2) onto each stud, and engage the hooks to the fuel rail. Install the nuts-(3) retaining there mover onto the studs and tighten until snug. Step 3. Note: EN-49248 will assist in the proper removal of the fuel rail assembly. Ensure that the following conditions are met: Turn the handles simultaneously in order to pull the fuel rail straight out along the fuel injector axis. DO NOT twist when pulling out on the fuel rail and injector assembly. Using EN-49248 remover, remove the fuel rail assembly-(1). Features & detailsFeatures
Product information
Additional InformationHave a question?Find answers in product info, Q&As, reviews Have a question?Top results Customer Q&A Customer Reviews Product info Post question There was a problem completing your request. Please try your search again later. Brief content visible, double tap to read full content.Full content visible, double tap to read brief content.VideosPage 1 of 1Start OverPage 1 of 1
Related posts |